Système Kanban

Takt time is the maximum time allowed to produce a product to meet customer demand. It is calculated by dividing the net available production time by the customer demand over that period. The formula is [latex]T = \frac{T_a}{D}[/latex], where T is the Takt time, Ta is the net available time, and D is the customer demand.

Just-in-Time (JIT) is a production strategy aimed at increasing efficiency and decreasing waste by receiving goods only as they are needed in the production process, thereby reducing inventory costs. This method requires precise forecasting and highly coordinated supply chains. The goal is to have the right materials, at the right place, at the right time, in the exact amount.

A foundational economic fact is that the total monetary volume of business-to-business (B2B) transactions significantly surpasses that of business-to-consumer (B2C) transactions. This is because a single finished consumer product often involves a long supply chain with multiple B2B transactions—from raw materials to manufacturing components to wholesale distribution—before the final B2C sale occurs.

The Fill Factor (FF) is a key parameter that determines the quality of a solar cell. It is the ratio of the maximum power a cell can produce ([latex]P_{max}[/latex]) to the theoretical power if it were an ideal voltage and current source ([latex]V_{oc} \times I_{sc}[/latex]). A higher fill factor indicates lower parasitic resistance losses and a more 'square' I-V curve.

The Toyota Production System is founded on the complete elimination of waste, categorized into 7 types, 3 main being described here: Muda (non-value-adding work), Muri (overburden), and Mura (unevenness). While Muda is the most commonly discussed, TPS recognizes that Muri and Mura are often the root causes of Muda and must be addressed first to achieve a truly lean system.

FTA is a top-down, deductive failure analysis technique. It starts with a potential undesired event (the "top event") and uses Boolean logic gates (AND, OR, etc.) to determine the combinations of component failures or human errors that could cause it. It provides a graphical model for understanding and quantifying system risk, identifying critical failure paths.

Pitting corrosion is a localized form of corrosion that leads to the creation of small holes, or 'pits,' in a metal. It is one of the most destructive forms because it is difficult to detect, predict, and design against. Pitting can cause catastrophic failure of a structure with only a small percentage of total mass loss.

High-Efficiency Particulate Air (HEPA) and Ultra-Low Particulate Air (ULPA) filters are critical cleanroom components. A HEPA filter must remove at least 99.97% of airborne particles 0.3 micrometers (µm) in diameter. An ULPA filter is even more efficient, removing 99.999% of particles 0.12 µm or larger. They work via a combination of interception, impaction, and diffusion.

FMEA is a systematic, bottom-up, inductive method for identifying potential failure modes in a system, product, or process. For each failure mode, it assesses the potential effects or consequences, their severity, likelihood of occurrence, and the ability to detect them. The goal is to prioritize and mitigate high-risk failure modes before they occur.

The PDCA cycle, also known as the Deming Cycle or Shewhart Cycle, is an iterative four-step management method used for the control and continuous improvement of processes and products. It provides a simple and effective approach for solving problems and managing change, ensuring that ideas are tested on a small scale before being implemented organization-wide.

A structured methodology for creating new products, typically involving analysis, concept development, and synthesis. It is an iterative cycle where designers research user needs, brainstorm ideas, create prototypes, and test them to refine the final product. This process ensures that the end product is both functional and meets market demands effectively before full-scale production.

Heijunka is the principle of production leveling or smoothing within the Toyota Production System. It involves averaging out the production volume and mix over a fixed period to eliminate peaks and valleys in workload. This creates a predictable and stable manufacturing environment, which is a prerequisite for implementing Just-in-Time (JIT) and standardized work effectively.

Takt time is a theoretical calculation representing the pace of customer demand ([latex]Available Time \div Demand[/latex]). In contrast, cycle time is an empirical measurement of the actual time taken to complete one unit of work at a specific process step. A core principle of lean manufacturing is to ensure that cycle time is consistently less than or equal to Takt time.

The use of computer systems to assist in the creation, modification, analysis, or optimization of a design. CAD software allows product designers and engineers to create precise 2D and 3D models, replacing manual drafting. This technology dramatically increases productivity, improves the quality of design, and facilitates better communication through detailed visualizations and simulations.