Takt Time Calculation Formula

Passivation is the process by which a material becomes 'passive,' meaning it is less affected by environmental factors such as corrosion. It involves the spontaneous formation of a very thin, non-reactive surface film that acts as a barrier, shielding the bulk material from further attack. This film is typically an oxide or nitride layer, a few nanometers thick.

The chloralkali process is an industrial method for the electrolysis of sodium chloride (NaCl) solution, known as brine. It is the primary source for producing chlorine (Cl₂), sodium hydroxide (NaOH), and hydrogen (H₂), which are essential commodity chemicals. Modern methods use a membrane cell to separate the anode and cathode products, ensuring high purity and efficiency.

Jidoka, often translated as "autonomation" or "automation with a human touch," is a pillar of the Toyota Production System. It empowers any machine or worker to halt the entire production line upon detecting an abnormality or defect. This prevents the mass production of faulty items and immediately highlights problems, enabling root cause analysis and permanent solutions.

Just-in-Time (JIT) is a production strategy aimed at increasing efficiency and decreasing waste by receiving goods only as they are needed in the production process, thereby reducing inventory costs. This method requires precise forecasting and highly coordinated supply chains. The goal is to have the right materials, at the right place, at the right time, in the exact amount.

A foundational economic fact is that the total monetary volume of business-to-business (B2B) transactions significantly surpasses that of business-to-consumer (B2C) transactions. This is because a single finished consumer product often involves a long supply chain with multiple B2B transactions—from raw materials to manufacturing components to wholesale distribution—before the final B2C sale occurs.

Kanban, meaning "visual card" or "signboard" in Japanese, is a scheduling system integral to the Toyota Production System. It uses visual cues, typically cards, to trigger action and manage workflow. It is a "pull" system that signals the need to move materials within a manufacturing facility or from an outside supplier into the production facility.

The Fill Factor (FF) is a key parameter that determines the quality of a solar cell. It is the ratio of the maximum power a cell can produce ([latex]P_{max}[/latex]) to the theoretical power if it were an ideal voltage and current source ([latex]V_{oc} \times I_{sc}[/latex]). A higher fill factor indicates lower parasitic resistance losses and a more 'square' I-V curve.

The Hall-Héroult process is the major industrial method for smelting aluminum. It involves dissolving alumina (aluminum oxide, Al₂O₃) in molten cryolite (Na₃AlF₆) and electrolyzing the molten salt bath. Aluminum metal is deposited at the cathode, while oxygen from the alumina reacts with the carbon anode, producing carbon dioxide. This process made aluminum widely available and affordable.

An empirical formula that describes how the available capacity of a battery decreases as the rate of discharge increases. The law is stated as [latex]C_p = I^k t[/latex], where [latex]C_p[/latex] is the capacity at a one-ampere discharge rate, [latex]I[/latex] is the discharge current, [latex]t[/latex] is the discharge time, and [latex]k[/latex] is the Peukert constant, specific to the battery type. It quantifies the inefficiency at high loads.

Pitting corrosion is a localized form of corrosion that leads to the creation of small holes, or 'pits,' in a metal. It is one of the most destructive forms because it is difficult to detect, predict, and design against. Pitting can cause catastrophic failure of a structure with only a small percentage of total mass loss.

High-Efficiency Particulate Air (HEPA) and Ultra-Low Particulate Air (ULPA) filters are critical cleanroom components. A HEPA filter must remove at least 99.97% of airborne particles 0.3 micrometers (µm) in diameter. An ULPA filter is even more efficient, removing 99.999% of particles 0.12 µm or larger. They work via a combination of interception, impaction, and diffusion.

FMEA is a systematic, bottom-up, inductive method for identifying potential failure modes in a system, product, or process. For each failure mode, it assesses the potential effects or consequences, their severity, likelihood of occurrence, and the ability to detect them. The goal is to prioritize and mitigate high-risk failure modes before they occur.

The PDCA cycle, also known as the Deming Cycle or Shewhart Cycle, is an iterative four-step management method used for the control and continuous improvement of processes and products. It provides a simple and effective approach for solving problems and managing change, ensuring that ideas are tested on a small scale before being implemented organization-wide.

A structured methodology for creating new products, typically involving analysis, concept development, and synthesis. It is an iterative cycle where designers research user needs, brainstorm ideas, create prototypes, and test them to refine the final product. This process ensures that the end product is both functional and meets market demands effectively before full-scale production.